mini digital storage oscilloscope review

I just got in the decidedly-cute DS203 Mini DSO (digital storage oscilloscope), weighing in at a mere 80 grams. We can reasonably guess from MiniDSO.com’s website that English is a second language for them. From what I understand, this is an open-source project so it will be fun to see what I can do with this.

SainSmart
K1, K2, K3, K4 & NAV A, NAV B across the top

Open Source

From what I’m reading in an online PDF, you can tether this to a PC and it appears as a USB drive, allowing you to make some modifications to the system itself. There appear to be examples for updating the splash screen logo and downloading/updating the application itself. Since this is likely some sort of Linux as the operating system then that will mean that I might be able to hack apart the update to find out what’s inside.

Precision

Looks like there are six adjustable potentiometers “under the hood” to allow you to calibrate it for accuracy. Most full-sized scopes have this feature but usually only about two of these adjustments, to be honest.

Accessories

It was fully assembled in the box although the online PDF suggests that there was a time when the customer was asked to fully put it together. This one included two probes (1X, 10X) which is pretty generous given that they can be as much as $30 each. It includes a small hex wrench for opening the back (access to those potentiometers). And finally, there was a tri-fold card with the barest of instructions possible. Here’s an example of a third of the instructions:

Turn on the power, enter the main page of the oscilloscope. Place in the standard signal (e.g. square wave 1 KHz, Vpp = 5V), insert X1 probe’s MCX end to CH A or CH B, and the probe to “WAVE OUT”. Check if the measurement value and the standard value are equal, calibrate if different.

Okay, I know enough about oscilloscopes to know what they mean here. I’ll translate this into English-geek for you:

Connect the X1 probe to the CH A connection, power on the oscilloscope and wait for the main screen to appear. Remove the probe’s cover to reveal the bare tip, putting this into the center of the  “WAVE OUT” port. Press Key 4 until the side menu is selected then use NAV 2 to select V1 from the options. Use NAV 1 to adjust the horizontal line until it coincides with the top part of the square wave, noting the voltage—as now measured—at the bottom of the screen. If this voltage is different than the reference 5.0V from the signal generator, then calibrate the meter by following these steps…

etc

At least that is the standard routine on a full-sized oscilloscope. I guess what I’m trying to say here is that the online PDF and tri-card documentation are pretty laughable and aren’t enough for the average person to learn how to use it.

On-screen Menu

The menu is pretty difficult so far. It’s clear that NAV A and B are used in selecting different values and moving from one place to another. K4 appears to move between the top set of menus to those down the right side of the screen.

Progress

After two full evenings playing with the interface, I’m beginning to understand some of the strange logic. Some of the hidden functionality is found when you press down on either the NAV A or NAV B sliders. It’s lost on the average person that these left/right sort of controls actually can be pressed as well. This opens up the missing features which were formerly lost on me.

So now, I can put an output wave on the screen (CH A–inserted probe to WAVE OUT), adjust the signal to a square wave of 20 microseconds in width, add a single reference voltage V1, hide V2 (and Channels B/C/D), adjust the T1 and T2 reference lines to match up to the waveform’s leading/trailing edges and then reference the delta at the bottom of the screen. Given the complexity of this as compared to the absence of a working manual, I’d call that rocket science.

The next step will be to attempt to calibrate it with a known good 5V power supply which I’ve just adjusted, having measured that with a good-quality multimeter.

Thoughts

I’m torn between moving ahead now with my own work and writing a useful how-to manual for this oscilloscope. It’s a shame that someone’s not written a good tutorial yet for this.

Update

And of course, I began working on rewriting a useful manual for this.

Advertisements

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s